manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 142

WARNING

Injury hazard. Before you operate the turning gear, make sure that no personnel are near
the flywheel, or in the engine.

16

Operate the turning gear to move the crankshaft in the applicable direction.

NOTE:

While the gear wheel turns, the carrier (008) moves the thrust pads. The first
thrust pad (007) will come out.

17

Keep a light tension on the manual ratchet (011) and the chain block (005) while the
thrust pad (007) moves up.

18

Remove the thrust pad (007).

19

Remove carefully the manual ratchet (010).

20

Use the chain block (005) and the manual ratchet (011) to move the thrust pad (007) to
the exhaust side.

21

Lower the thrust pad (007) on to a stable area.

22

Do 

Step 15

 to 

Step 21

 for the remaining thrust pads you must remove.

X72DF

AA00-1203-00AAA-520A-A

Maintenance Manual

Thrust bearing - remove the pads

Winterthur Gas & Diesel Ltd.

- 142 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands