manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 441

CAUTION

Damage Hazard. Damage will occur to an incorrectly connected toggle lever. Make sure
that you connect the toggle lever correctly.

29

Connect the toggle lever (001, 

Figure 8-41

) to the crosshead (002). Make sure that the

toggle lever is in the position shown.

Fig 8-45

 Toggle lever - attach

30

Remove the platform, refer to section 

8.1.3 Crankshaft - remove the work platform

.

31

Do the a check of the clearances, refer to section 

8.6.2 Crosshead - do a check of the

clearances

.

32

Make sure that the piston rod foot (004, 

Figure 8-46

) is clean and has no damage.

X72DF

AA00-3303-00AAA-720A-A

Maintenance Manual

Connecting rod - install

Winterthur Gas & Diesel Ltd.

- 441 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands