manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 225

PROCEDURE

1

Remove the piston rod gland together with the piston, refer to the related procedure.

2

Remove and discard the two O-rings (002, 

Figure 7-27

).

3

Remove the four screws and nuts (003, 006).

4

Push the two parts of the housing (001, 005) away from the piston rod.

5

Remove the two parts of the housing (001, 005).

Fig 7-27

 Piston rod gland - remove and install

6

Remove the parts that follow:

•

Tension springs (002 and 005, 

Figure 7-28

)

•

Scraper rings (001, 007)

•

Gaskets (003, 004)

•

Ring supports (006).

X72DF

AA00-2303-00AAA-520A-A

Maintenance Manual

Piston rod gland - remove

Winterthur Gas & Diesel Ltd.

- 225 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands