manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

The WinGD X62DF maintenance manual is available for download for free on our website. This comprehensive manual provides all the information needed to properly care for and maintain your engine. Download it now from manualshive.com to ensure long-lasting performance of your WinGD X62DF engine.

Share
Download
background image

PROCEDURE

1

Remove the protection cover (001, 

Figure 6-25

) from all tie rods (002).

2

Clean the faces of the intermediate rings (004).

3

Do a check of the pre-tension of the first pair of tie rods a-a, refer to section 

4.4 Do a

check of the pre-tension

.

NOTE:

Start with the tie rods in the middle of the engine a-a, then b-b etc.

4

Do 

Step 3

 again for the other tie rods.

5

Apply a layer of Molykote paste G to the threads of the tie rods (002) to prevent
corrosion.

6

Attach the protection covers (001).

Fig 6-25

 Pre-tension checks

CLOSE UP

•

None

X72DF

AA00-1903-00AAA-360A-A

Maintenance Manual

Tie rod - do a check of the pre-tension

Winterthur Gas & Diesel Ltd.

- 157 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for X62DF

Rato 125-S Owner'S Manual preview
125-S
Brand: Rato Pages: 32
Vascat MAC R Series Instruction And Maintenance Manual preview
MAC R Series
Brand: Vascat Pages: 60
SCHABMULLER TSA 200-100-220 Operating And Maintenance Instructions Manual preview
TSA 200-100-220
Brand: SCHABMULLER Pages: 56
Shindaiwa DGW400DMK Owner'S And Operator'S Manual preview
DGW400DMK
Brand: Shindaiwa Pages: 48
Plettenberg HP 370 Operating Manual preview
HP 370
Brand: Plettenberg Pages: 26
M.T.H. Premier U30C Operator'S Manual preview
Premier U30C
Brand: M.T.H. Pages: 26
Northern Lights NL773LW4 Operator'S Manual preview
NL773LW4
Brand: Northern Lights Pages: 42
Bartec Varnost 4KTCR 250 Directions For Use Manual preview
4KTCR 250
Brand: Bartec Varnost Pages: 48
Rotax 912 A Operator'S Manual preview
912 A
Brand: Rotax Pages: 84
Rotax 915 iS 3 A Installation Manual preview
915 iS 3 A
Brand: Rotax Pages: 166
MINN KOTA Endura 50 Schematic/Electrical Parts preview
Endura 50
Brand: MINN KOTA Pages: 3
MINN KOTA 1810244 Quick Start Manual preview
1810244
Brand: MINN KOTA Pages: 4
Andersen RA2028001300 Product Manual preview
RA2028001300
Brand: Andersen Pages: 20
Saito FA-200R3 Instructions preview
FA-200R3
Brand: Saito Pages: 5
Saito FA-56B Operating Instructions Manual preview
FA-56B
Brand: Saito Pages: 6
PST Jets J600R Instruction Manual preview
J600R
Brand: PST Jets Pages: 44
Electric Drive Engineering EDE Installation & Operating Manual preview
EDE
Brand: Electric Drive Engineering Pages: 19
Zenoah 967286301 Owner'S Manual preview
967286301
Brand: Zenoah Pages: 24

Brands by name

Popular brands

Load more brands