WinGD X62DF Maintenance Manual Download Page 159

Page: 159 / 902

PROCEDURE

Remove the protection cover (001,

Figure 6-26

) from the tie rods (004).

Clean the surface of the intermediate ring (003).

Attach the two pre-tensioning jacks to the applicable tie rod (004).

Remove the round nut (002), refer to section

4.3 Loosen a round nut with a pre-

tensioner

Loosen the two set screws (006).

Use two round nuts to remove the tie rod (004) from the nut (007).

Attach an eye bolt to the tie rod (004).

Attach the engine room crane to the eye bolt.

Operate the engine room crane to lift the tie rod (004) from the cylinder jacket (005).

Move the tie rod (004) to an applicable area.

Fig 6-26

Tie rod - removal

CLOSE UP

•

None

X72DF

AA00-1903-00AAA-520A-A

Maintenance Manual

Tie rod - remove

Winterthur Gas & Diesel Ltd.

- 159 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands

WinGD X62DF, Maintenance Manual

Search results

Summary of Contents for X62DF

Reviews:

Brands by name

Popular brands