manualshive.com logo in svg

WinGD X62DF, Maintenance Manual

Share
Download
WinGD X62DF Maintenance Manual Download Page 207

PROCEDURE

1

Apply Molycote G-Rapid Plus to the disassembly / assembly tool (006, 

Figure 7-18

).

2

Remove the screws (003) on each side of the compensator (001).

3

Put the tool (006) in position on the compensator (001) as shown.

NOTE:

The tool (006) is shorter than the installed length of the compensator (001).

4

Attach the tool (006) to the flanges of the compensator (001) with the four screws (007).

5

Tighten the four screws (007).

6

Tighten equally the two bolts (005) to compress the compensator (001).

7

Continue to tighten the bolts (005) until you can remove the compensator (001).

8

Carefully remove the tool (006) together with the compensator (001).

9

Make sure that the six O-rings (008) (on the flange couplings) are serviceable. If
necessary, replace the O-rings.

10

Remove the tool (006) from the compensator (001).

11

Put the compensator (001) in a clean, dry area.

Fig 7-18

 Compensator - remove

12

Put an oil tray under the gas admission valve (GAV) (005, 

Figure 7-19

).

13

Make sure that the power supply to the rail valve (010) is set to off.

14

Disconnect the electrical connections to the rail valve (010) and the valve stroke sensor
(007).

15

Loosen the four screws (002).

16

Remove the pipe.

NOTE:

During this step, make sure that you do not damage the sealing face of the
pipe (001).

X72DF

AA00-2140-00AAA-520A-A

Maintenance Manual

Gas admission valve - remove

Winterthur Gas & Diesel Ltd.

- 207 -

Issue 002 2020-10

Summary of Contents for X62DF







































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands