background image

Vista

®

 Underground 

Distribution Switchgear

Pad-Mounted, Vault-Mounted, and UnderCover™ Styles

September 9, 2019
©  S&C Electric Company 2001-2019, all rights reserved

Instruction Sheet  681-525

Installation and Operation  

of Portable Motor Operator

Table of Contents

Section Page

Section Page

Introduction

Qualified Persons   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Read this Instruction Sheet    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Retain this Instruction Sheet .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  2
Proper Application    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2
Warranty   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

Safety Information

Understanding Safety-Alert Messages  .  .  .  .  .  .  .  .  .  .  . 3
Following Safety Instructions   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Replacement Instructions and Labels    .  .  .  .  .  .  .  .  .  .  . 3
Location of Safety Labels   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Safety Precautions

   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

Components

General   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6 

Installation

Installing the Portable Motor Operator   .  .  .  .  .  .  .  .  .  .  . 7 

Operation

Opening, Closing, or Grounding .   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .12 

Removal

Removing the Portable Motor Operator   .  .  .  .  .  .  .  .  .  .14 

Troubleshooting

If the Remote Control READY Light  

Does Not Light .    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .15

Fault Conditions on the S&C-Furnished Ac-Input 

Power Supply   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .15

Summary of Contents for Pad-Mounted Series
















Reviews: