Volkswagen CC 2012 Workshop Manual Download Page 196

Page: 196 / 222

Installing:
– Fit connectors to engine control unit and slide locking devices

onto stop in -direction of arrow-.

– Install engine control unit into retaining frame and push up‐

wards in the direction of the -arrow-.

– Install wiper arms and plenum chamber cover ⇒ General body

repairs, exterior; Rep. gr. 50 ; Bulkhead; Removing and in‐

stalling plenum chamber cover .

6.2

Removing and installing engine (motor)

control unit - J623- with protective hous‐

ing

Note

♦

If the engine control unit is to be replaced, connect vehicle

diagnostic tester and carry out the guided function “Replacing

engine control unit”.

♦

The shear-head bolt threads may coated with locking com‐

pound. To simplify removal, the shear-head bolts can be heat‐

ed using hot air blower - VAS 1978/14- . When doing this,

ensure that no adjacent cables, connectors or components are

damaged!

Removing:
– Switch off ignition.
– Remove wiper arms and plenum chamber cover ⇒ General

body repairs, exterior; Rep. gr. 50 ; Bulkhead; Removing and

installing plenum chamber cover .

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

190

Rep. gr.24 - Mixture preparation - injection

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands