Volkswagen CC 2012 Workshop Manual Download Page 139

Page: 139 / 222

Oil filter, oil pressure switch

⇒ “2.1 Assembly overview - oil filter housing, oil pressure switch”,

page 133
⇒ “2.2 Checking oil pressure and oil pressure switch”,

page 135

2.1

Assembly overview - oil filter housing, oil

pressure switch

Note

♦

If large quantities of metal chips and abraded material are

found during engine repair, this may indicate that the crank‐

shaft bearings or conrod bearings are damaged. To avoid any

subsequent damage, the following work must be carried out

following the repair:

♦

Thoroughly clean oil channels.

♦

Renew oil spray jets.

♦

Renew engine oil cooler.

♦

Renewing oil filter.

♦

The oil level must not be above the max. marking on the dip‐

stick - danger of damage to the catalytic converter! Markings

⇒ page 131

, Checking engine oil level.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

2. Oil filter, oil pressure switch

133

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands