Volkswagen CC 2012 Page 19 Workshop Manual Download

Page: 19 / 222

– Unscrew bolt -2- and lay filler neck -1- for washer fluid reservoir

to front.

– Unplug connector -3-.
– Unscrew bolts -5- and lay coolant expansion tank -4- on en‐

gine with the hoses connected.

Note

Undo the bolts on the engine mounting and gearbox mounting by

one turn.

WARNING

Danger of injury due to coolant.

♦ Do not open the air conditioner refrigerant circuit.

So that engine can be removed even without opening refrigerant

circuit:
– Remove air conditioner compressor from ancillary bracket ⇒

Heating, air conditioning; Rep. gr. 87 ; Air conditioner com‐

pressor; Removing and installing air conditioner compressor

from and to bracket .

Caution

Danger of damage to coolant lines and hoses.

♦ Do NOT stretch, kink or bend refrigerant lines and hoses.

– Secure air conditioner compressor, as shown, to bumper cov‐

er with fastening strap - T10038- and appropriate underlay

-A-. Slide fastening strap - T10038- as far as possible towards

securing bolt -arrow-.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Removing and installing engine

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands