Volkswagen CC 2012 Workshop Manual Download Page 91

Page: 91 / 222

– Tighten bolt -1- for guide rail.

– Insert inlet camshaft adjuster »24E« into timing chain in such

a way that the copper-coloured chain link is aligned with the

marking on the camshaft adjuster. Bolt camshaft adjuster onto

camshaft and tighten bolt hand-tight.

– Insert exhaust camshaft adjuster »32A« into timing chain in

such a way that copper-coloured chain link is aligned with

marking on camshaft adjuster. Bolt camshaft adjuster onto

camshaft and tighten bolt hand-tight.

– Check position of copper coloured chain links to adjustment

markings.

Note

The copper coloured chain links no longer align with the adjust‐

ment markings once the crankshaft has been turned.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

3. Chain drive

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands