Volkswagen CC 2012 Page 159 Workshop Manual Download

Page: 159 / 222

• Installation position: the edges on thermostat and on housing

must align -arrows-.

– Moisten new seal with coolant and fit on coolant connection.
– Fit coolant connection with seal and tighten bolts alternately

and diagonally.

Specified torque: 5 Nm.
– Add coolant

⇒ page 142

– Install noise insulation ⇒ General body repairs, exterior; Rep.

gr. 66 ; Noise insulation; Assembly overview – noise insula‐

tion .

2.4

Checking thermostat

Note

The thermostat can be tested with the “Guided Fault Finding” un‐

der “Selection of functions and components”.

– Remove thermostat

⇒ page 152

– Heat thermostat in water.
• Starts to open at 80 °C
• Opening at 94°C: 9 mm

2.5

Removing and installing continued cool‐

ant circulation pump - V51-

Location of continued coolant circulation pump - V51-
The continued coolant circulation pump - V51- is secured to an‐

cillary unit bracket -arrow-.
– To remove, ancillary bracket must be removed from cylinder

block

⇒ page 33

The continued coolant circulation pump - V51- is bolted to ancil‐

lary bracket to specified torque of 8 Nm.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

2. Coolant pump, regulation of cooling system

153

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands