Volkswagen CC 2012 Workshop Manual Download Page 31

Page: 31 / 222

♦ Torque wrench - V.A.G 1332-
Procedure

Note

It is not necessary to remove the air filter if only the assembly

mounting at the engine end is to be adjusted.

– Remove air filter

⇒ page 174

– Remove air filter bracket

⇒ page 174

Caution

The racks - 10 - 222 A /1- must not be placed on the bolted on

sheet metal of the wings. These may otherwise be damaged.

– Tighten shackle - 10 - 222 A /12- on right lifting eye.
– Fit support bracket - 10 - 222 A- with frame - 10 - 222 A /1- as

shown and take up weight of engine in installation position.

Adjusting engine mountings:
– Unbolt engine side of assembly mounting from engine bracket

-arrows-.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

2. Assembly mountings

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands