Volkswagen CC 2012 Workshop Manual Download Page 195

Page: 195 / 222

Engine control unit

⇒ “6.1 Removing and installing engine (motor) control unit J623

”, page 189
⇒ “6.2 Removing and installing engine (motor) control unit J623

with protective housing”, page 190

6.1

Removing and installing engine (motor)

control unit - J623-

Note

If the engine control unit is to be replaced, connect vehicle diag‐

nostic tester and carry out the guided function “Replacing engine

control unit”.

Removing:
– Switch off ignition.
– Remove wiper arms and plenum chamber cover ⇒ General

body repairs, exterior; Rep. gr. 50 ; Bulkhead; Removing and

installing plenum chamber cover .

– Push retaining frame down in -direction of arrow- and remove

engine control unit.

– Push locking devices of connectors in -direction of arrow- and

pull off connectors.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

6. Engine control unit

189

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands