Volkswagen CC 2012 Workshop Manual Download Page 135

Page: 135 / 222

– Unscrew oil pump securing bolts -arrows-.

– Lever oil pump out evenly at lugs -arrows-.
Installing:

Note

♦

Do not tilt oil pump when installing.

♦

Renew O-ring and securing bolt for the sprockets.

♦

Insert securing bolts for oil pump with locking fluid.

– Install oil pump, coat securing bolts -arrows- with locking

agent, then tighten bolts. Specified torque

⇒ Item 8 (page 123)

– Set crankshaft to TDC position.
• Ground tooth of drive sprocket -arrow- must align with bearing

joint.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Sump, oil pump

129

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands