Volkswagen CC 2012 Workshop Manual Download Page 210

Page: 210 / 222

♦ Chain-type pipe cutter - VAS 6254-
♦ Safety glasses
Procedure

WARNING

To avoid injury from metal shavings, wear eye protection and

protective clothing.

– Cut through exhaust pipe at separation point using e.g. pneu‐

matic sabre saw - V.A.G 1523 A- perpendicular to pipe.

♦ Separating point on exhaust pipe -arrows 1- for rear right si‐

lencer.

♦ Marking -arrow 2- is necessary for the installation position of

the clamp

⇒ page 205

♦ Separating point on exhaust pipe -arrows 1- for rear left si‐

lencer.

♦ Marking -arrow 2- is necessary for the installation position of

the clamp

⇒ page 205

– Install rear silencer and connect it to the middle silencer with

a clamp. Installation position and specified torque of clamp

⇒ page 205

– Adjust the exhaust system so that distance -a- on left and right

is the same.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

204

Rep. gr.26 - Exhaust system

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands