Volkswagen CC 2012 Workshop Manual Download Page 147 | Manualshive

Page: 147 / 222

background image

Self-test of cooling system tester - V.A.G 1274 B-
– Operate cooling system tester - V.A.G 1274 B- several times.

– Build up a pressure of 3.0 bar on cooling system tester .
– Observe pressure on pressure gauge of cooling system tester

for 30 seconds.

If no pressure builds up or if the pressure drops again:
The cooling system tester - V.A.G 1274 B- is leaking and should

not be used.

Checking cooling system for leaks
• Engine at operating temperature.

WARNING

The cooling system is under pressure when the engine is hot!
Danger of scalding due to steam and hot coolant.
Cover filler cap on expansion tank with a cloth and open care‐

fully to release pressure.

– Open cap -1- on coolant expansion tank.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Cooling system/coolant

141

«
...
145
146
147
148
149
...
»

Summary of Contents for CC 2012































































































































































































































Reviews:

No comments

Related manuals for CC 2012

Brand: Ultra Start Pages: 8

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Escalade ESV 2014

Brand: Cadillac Pages: 508

Brand: Hama Pages: 2

Brand: Jeep Pages: 1528

Brand: Baja Designs Pages: 5

Brand: Metra Electronics Pages: 2

Brand: Unex Pages: 30

ZapCharger Portable C1

Brand: ZAPTEC Pages: 20

Brand: Billien Pages: 2

Brand: Lexus Pages: 28

Brand: Toyota Pages: 36

1995 Roadmaster

Brand: Buick Pages: 340

Brand: Lexus Pages: 878

Brand: Pyle Pages: 14

Brand: Adaptiv Mini Pages: 4

Brand: Technaxx Pages: 59

Brand: American muscle Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands