Volkswagen CC 2012 Workshop Manual Download Page 211

Page: 211 / 222

1.3

Installation position of clamp

Installation position of front clamp
– Align clamp -1- to marking on exhaust pipe -2- -Arrow- points

in direction of travel.

• Dimension -a- = 5 mm.
• Specified torque: 25 Nm
• Bolted connection faces to right.

– Install clamp so that end of bolt -arrow- does not extend be‐

yond lower edge of clamp.

Installation position of clamp rear (for repair)
– Align the clamp with the mark on the exhaust pipe.
• Specified torque: 25 Nm

– Install clamp so that end of bolt -arrow- does not extend be‐

yond lower edge of clamp.

• Bolted connection faces rear.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

1. Exhaust pipes and silencers

205

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands