Volkswagen CC 2012 Page 193 Workshop Manual Download

Page: 193 / 222

Procedure:

WARNING

The fuel line is under pressure.
Fuel poses danger of injury to eyes and skin.
Wear protective goggles and protective clothing to avoid injury

and contact with the skin. Wrap a cloth around the connection

before loosening hose connections. Then reduce pressure by

carefully opening the connection.

– Pull connector off fuel pressure sender - G247- -A- and re‐

move fuel pressure sender using open ring spanner.

– Unscrew plug -2- and screw fuel pressure sender - G247- into

tester - VAS 6394/1- . Specified torque: 22 Nm.

– Moisten tapered seal of adapter - VAS 6394/3- using clean

engine oil and screw into fuel rail -arrow-. Specified torque:

22 Nm.

CC 2012 ➤ , Passat 2011 ➤ , Passat Variant 2011 ➤

6-cylinder direct-injection engine (3.6 l engine, 4V) - Edition 06.2019

5. Senders and sensors

187

Summary of Contents for CC 2012































































































































































































































Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands

Volkswagen CC 2012, Workshop Manual

Search results

Summary of Contents for CC 2012

Reviews:

Related manuals for CC 2012

Brands by name

Popular brands