VESPA 150 Service Station Manual Download

Page: 221 / 249

Refitting

- To fit, follow the removal steps but in reverse order; be careful to tighten to the prescribed torques.

Locking torques (N*m)

Shock absorber/chassis nut torque

20 - 25 Nm

Lower shock absorber clamp

40 to 45

Centre-stand

REMOVAL

- Use a jack to support the vehicle properly.

- Remove the two return springs from the centre

stand.

- Undo the fixing nut on the left-hand side of the

engine.

- Remove the pin from the right side.

- Remove the centre stand.

FITTING

- On refitting tighten the nut to the specified torque.

Locking torques (N*m)

Centre stand pin

40 to 45

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Suspensions

SUSP - 221

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands