VESPA 150 Service Station Manual Download Page 139

Page: 139 / 249

Removing the wheel axle bearings

- Support the hub cover properly to avoid damag-

ing the sealing surface with the crankcase

- Remove the Seeger ring from the outside.

- Operating on the inside, remove the oil seal.

- Remove the wheel axle bearing using the specific

tool.

Specific tooling

020376Y

Adapter handle

020364Y

25-mm Guide

020359Y

42 x 47-mm adaptor

Removing the intermediate gear bearing

- Remove the bearing using the specific tools.

Specific tooling

001467Y013

Calliper to extract 15-mm diame-

ter bearings

001467Y009

Bell for OD 42-mm bearings

Inspecting the hub shaft

- Check the three shafts and the intermediate gear

for wear or distortion of the toothed surfaces, the

bearing housings, and the oil seal housings.

- If faults are found, replace the damaged parts.

Characteristic

Driven pulley shaft

A: 22(-0.01 -0.02)mm

Wheel axle

B: 15(-0.010 -0.020)mm

C: 25(-0.007 -0.020)mm

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Engine

ENG - 139

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 139 / 249

Search results

Summary of Contents for 150

Reviews: