VESPA 150 Service Station Manual Download Page 132

Page: 132 / 249

Refitting the driven pulley

- Check that the faying surfaces of the 2 half-pul-

leys and the belt do not show any signs of wear,

scoring or grease.

- Insert the new oil seals and O-rings on the mov-

able half-pulley.

- Fit the half-pulley on the bushing with the appro-

priate protection sheath.

- Make sure the pins and collar are not worn, refit

the pins and the collar.

- Using a curved-spout grease gun, lubricate the

driven pulley unit with approximately 6 g of grease.

Apply the grease through one of the holes in the

bushing until grease comes out through the hole

on the opposite side. This procedure is necessary

to prevent the presence of grease beyond the O-

rings.

Specific tooling

020263Y

Sheath for fitting the driven pulley

Recommended products

AGIP GREASE SM 2

Gray black smooth-tex-

tured lithium grease, containing molybdenum
disulphide.

Inspecting the clutch spring

- Measure the length of the movable driven half-

pulley spring, when unloaded.

Characteristic

Standard length:

106 mm

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 132

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 132 / 249

Search results

Summary of Contents for 150

Reviews: