VESPA 150 Service Station Manual Download Page 184

Page: 184 / 249

- Fuel pump

- H.V. coil

- Injector

The control unit is fitted with a self-diagnosis sys-

tem connected to a warning light on the instrument

panel.

Failures are detected and restored by the diagnostic tester.

In any case, when the fault is no longer present, data storage is automatically wiped clean after 16

cycles of use (cold starting, running at regular engine temperature, stop).

The diagnostic tester is also required for adjusting idle speed carburetion.

Specific tooling

020922Y

Diagnosis Tool

The injection control unit has a decoder for the an-

ti-theft immobilizer system.

The injection control unit is connected to a diag-

nostic LED on the instrument panel that also car-

ries out the deterrent flashing functions.

Precautions

Troubleshooting tips

1 An injection system failure is more likely to be due to the connections than to the components.

Before troubleshooting the injection system, carry out the following checks:

: Electrical power supply

a. Battery voltage

b. Blown fuse

c. Relays

d. Connectors

: Chassis ground

Injection

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

INJEC - 184

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 184 / 249

Search results

Summary of Contents for 150

Reviews: