manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 148 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 148

- Before screwing in the flywheel extractor the pro-

tection tool provided in the specific tool must be

positioned.

Specific tooling

020933Y

 

Flywheel extractor

- Acting on the extractor, remove the flywheel to-

gether with the starting sprocket and intermediate

gear.

Inspecting the flywheel components

- Check the integrity of the internal plastic parts of the flywheel and the Pickup control plate.

- Check the integrity of the internal plastic parts of the flywheel and the Pickup control plate.

Refitting the flywheel magneto

- Perform the procedure in reverse order of disassembly, taking care to tighten to specified torque.

Locking torques (N*m)

Flywheel fixing nut

 

100 to 110

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 148

Summary of Contents for 150


























































































































































































































































Reviews:

No comments