VESPA 150 Service Station Manual Download Page 10

Page: 10 / 249

Specification

Desc./Quantity

Cooling

Forced-air circulation cooling.

Electric

Electric starter

Ignition

Electronic capacitive discharge ignition, with variable advance

and separate H.V. coil.

Ignition advance

Three-dimensional map managed by control unit

Spark plug (125 cm³)

NGK CR8EB

Electrode gap

0.7 - 0.8 mm

Fuel system

Electronic injection with Ø 26 mm throttle body, single injector

Fuel

Unleaded petrol (95 RON)

Exhaust silencer

Absorption-type exhaust muffler with catalytic converter.

Emissions compliance

EURO 3

150

³ ENGINE SPECIFICATIONS

Specification

Desc./Quantity

Type

Single-cylinder, 4-stroke

Engine capacity

155 cm³

Bore x stroke

58.0 x 58.6 mm

MAX. power

9.5 kW at 7,750 rpm

MAX. torque

12.8 Nm at 6,500 rpm

Idle speed

(1,750±100) rpm

Valve clearance (when cold)

intake: 0.08 mm exhaust: 0.08 mm

Timing system

3 valves (2 intake, 1 drainage). single overhead camshaft

chain-driven.

Transmission

CVT expandable pulley variator with torque server, V-belt, self-

ventilating dry automatic centrifugal clutch and transmission

housing with forced-circulation air cooling.

Final reduction

with gear reduction unit in oil bath.

Lubrication

Engine lubrication with lobe pump (inside crankcase), chain-

driven, with double filter: mesh and paper.

Cooling

Forced-air circulation cooling.

Electric

Electric starter

Ignition

Electronic capacitive discharge ignition, with variable advance

and separate H.V. coil.

Ignition advance

Three-dimensional map managed by control unit

Spark plug (150 cm³)

NGK CR8EB

Electrode gap

0.7 - 0.8 mm

Fuel system

Electronic injection with Ø 28 mm throttle body, single injector

Fuel

Unleaded petrol (95 RON)

Exhaust silencer

Absorption-type exhaust muffler with catalytic converter.

Emissions compliance

EURO 3

Transmission

RANSMISSION

Specification

Desc./Quantity

Transmission

CVT expandable pulley variator with torque server, V-belt, self-

ventilating dry automatic centrifugal clutch and transmission

housing with forced-circulation air cooling.

Final reduction

with gear reduction unit in oil bath.

Capacities

CAPACITY

Specification

Desc./Quantity

Engine oil

1340 (of which 120 cm³ in the filtering cartridge) (45.31 US fl

oz (of which 4.06 US fl oz in the filtering cartridge))

Hub oil

270 cm³ (9.13 US fl oz)

Fuel tank capacity

8 ± 0.1 l (2.11 ± 0.03 UK gal)

Characteristics

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

CHAR - 10

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 10 / 249

Search results

Summary of Contents for 150

Reviews: