VESPA 150 Service Station Manual Download Page 11

Page: 11 / 249

Frame and suspensions

RAME

AND

USPENSION

Specification

Desc./Quantity

Chassis

Stamped plate body with welded structural reinforcements.

Front suspension

Single arm with helical spring and single double-acting hy-

draulic shock absorber.

Rear suspension

Double-acting shock absorber, adjustable to four positions at

preloading.

Brakes

BRAKES

Specification

Desc./Quantity

Front brake

Ø 200-mm disc brake with hydraulic control activated by han-

dlebar right-side lever.

Rear brake

Ø 140-mm drum brake with mechanical control activated by

handlebar left-side lever.

Wheels and tyres

WHEELS AND TYRES

Specification

Desc./Quantity

Wheel rim type

Light alloy.

Front wheel rim

11'' x 2.50

Rear wheel rim

11'' x 2.75

Front tyre

Tubeless, 110/70 - 11'' 45L

Rear tyre

Tubeless, 120/70 - 11'' 56L

Front tyre pressure

1.6 bar

Rear tyre pressure

1.8 bar

Tightening Torques

FRAME ASSEMBLY

Name

Torque in Nm

Frame-swinging arm bolt

44 to 52 (32.5 to 38.4 lbf*ft)

Engine-swinging arm bolt

40 - 45 (29.5 - 33.2 lb*ft)

Silent block-swinging arm retaining bolts

40 - 45 (29.5 - 33.2 lb*ft)

Centre stand pin

40 - 45 (29.5 - 33.2 lb*ft)

STEERING ASSEMBLY

Name

Torque in Nm

Upper steering ring nut

35 to 40 (25.8 to 29.5 lbf*ft)

Lower steering ring nut

12 to 14 (8.9 to 10.3 lbf*ft)

Handlebar fixing screw

50 to 55 (36.9 to 40.6 lbf*ft)

FRONT BRAKE

Name

Torque in Nm

Brake fluid pump-hose joint

8 to 12 (5.9 to 8.9 lbf*ft)

Brake fluid pipe-calliper fitting

20 to 25 (14.8 to 18.4 lbf*ft)

Screw tightening calliper to support

20 to 25 (14.8 to 18.4 lbf*ft)

Brake disc screw (°)

5 to 6.5 (3.7 to 4.8 lbf*ft)

Oil bleed valve (on the calliper)

10 to 12 (7.4 to 8.9 lbf*ft)

Handlebar pump

7 to 10 (5.2 to 7.4 lbf*ft)

Brake pump reservoir screw

15 to 20 (11.1 to 14.8 lbf*ft)

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Characteristics

CHAR - 11

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 11 / 249

Search results

Summary of Contents for 150

Reviews: