manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 209 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 209

To remove the second NADELLA, use the tool fit-

ted with part 2 instead of part 1, on the side oppo-

site the one shown in the figure.

N.B.

DURING THE REMOVAL OPERATIONS DESCRIBED
ABOVE, THE ROLLER BUSHINGS ARE DESTROYED
WHEN THE EXTRACTOR IS USED. UPON REFITTING, IT IS
THEREFORE NECESSARY TO USE NEW BUSHINGS AS
WELL AS A NEW PIN, NEW SEALING RINGS AND DUST
GAITER.

Specific tooling

020021Y

 

Front suspension service tool

Connect the swinging hub to the steering tube with

the guiding pin.

- Use the tool fitted with part 3 on the stem and part

4.

Lubricate the pin with recommended grease and

insert it temporarily on the swinging hub, move the

tool handgrip until part 3 is fully inserted on the

steering tube.

After fitting the pin, insert the two spacers, slightly

hitting them with the mallet.

N.B.

BEFORE PROCEEDING WITH THE DESCRIBED FITTING,
PLACE THE TWO DUST GAITER RINGS ON THE SWING-
ING HUB AS SHOWN IN THE FIGURE.

Specific tooling

020021Y

 

Front suspension service tool

Recommended products

AGIP GREASE SM 2

 

Gray black smooth-tex-

tured lithium grease, containing molybdenum
disulphide.

-

Insert the sealing ring on the pin and the roller

bushing with its wedging washer at the same time.

- Remove the tool and the part 5 (guide), which has

been partially ejected during the previous pin fitting

phase, and leave part 4 always fitted.

- Replace part 3 with part 16 (on the stem).

- By moving the tool handgrip, push the wedging

washer - roller bushing - seal ring unit, placing part

16 until it stops on the swinging hub.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Suspensions

SUSP - 209

Summary of Contents for 150


























































































































































































































































Reviews:

No comments