VESPA 150 Service Station Manual Download

Page: 130 / 249

Pin retaining collar

- Simultaneously turn and pull the collar manually

to remove it.

N.B.

USE TWO SCREWDRIVERS IF YOU HAVE ANY DIFFICUL-
TY.

N.B.

BE CAREFUL NOT TO PUSH THE SCREWDRIVERS IN TOO
FAR TO AVOID DAMAGE THAT COULD COMPROMISE
THE O-RING SEAL.

Removing the driven half-pulley bearing

- Remove the retainer ring using two flat blade

screwdrivers.

- Using a hammer and pin, knock the ball bearing

out as shown in the figure.

- Remove the bearing and the rollers with the spe-

cific extractor.

N.B.

REST THE HALF-PULLEY ON A WOODEN SURFACE TO
AVOID DAMAGING ITS THREADED BUSHING. ALSO DO
THIS UPON REMOVAL.

Specific tooling

001467Y008

Calliper to extract 17-mm diame-

ter bearings

001467Y009

Bell for OD 42-mm bearings

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 130

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands