VESPA 150 Service Station Manual Download

Page: 106 / 249

Replace the key and store it if necessary. If the error persists, check the electrical characteristics and

the continuity of the antenna circuit:

- Disconnect the antenna connector and check the correct resistance value at the ends.

- Check wiring continuity between the antenna and the engine control unit and restore if necessary.

Electric characteristic

Resistance at 20°C

7.66 ± 5%

H.V. COIL

Function

Allows generation of the electrical discharge on

the spark plug, with an increase of voltage.

Pin-out:

1. Control unit power

2. Ground lead

ELECTRICAL ERRORS

H.V. coil P0351 -

open circuit.

Error cause

Open circuit: circuit interruption.

Troubleshooting

Open circuit:

- Carry out the check procedure of the coil and control unit connectors.

- Check the ground and battery-powered insulation of coil PIN 1.

- Verify continuity of the cabling between the coil and control unit: Coil PIN 1 - control unit PIN 8. If there

is no continuity, restore the cable harness.

- Check the ground connection of coil PIN 2. If necessary, restore the cable harness.

- If the above tests provided a positive result, the coil should be replaced.

INJECTOR

Function

Provide the correct amount of fuel at the correct

time.

Operation / Operating principle

Injector coil is excited for the petrol passage to

open.

Pin-out:

Electrical system

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ELE SYS - 106

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands