manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 169 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 169

Locking torques (N*m)

Intake manifold fixing screws

 

10.8 to 12.8

Crankcase - crankshaft

Splitting the crankcase halves

- Undo the eight crankcase coupling screws.

- Separate the crankcase halves while keeping the

crankshaft in one of these two halves.

- Only after the halves have been separated, can

the crankshaft be checked.

CAUTION

WHILE OPENING THE CRANKCASES AND REMOVING
THE CRANKSHAFT, CHECK THAT THE THREADED
SHAFT ENDS DO NOT INTERFERE WITH THE MAIN BUSH-
INGS. FAILURE TO OBSERVE THIS PRECAUTION CAN
DAMAGE THE MAIN BUSHINGS.

CAUTION

GI

Ữ

 TR

Ụ

C KHU

Ỷ

U N

Ằ

M 

Ở

 M

Ộ

T TRONG HAI N

Ử

A C

Ủ

A

VÁCH MÁY TRONG KHI TÁCH R

Ờ

I VÁCH MÁY. N

Ế

U THAO

TÁC KHÔNG T

Ố

T, TR

Ụ

C KHU

Ỷ

U CÓ TH

Ể

 R

Ơ

I.

- Remove the gasket and be careful with the align-

ment dowels.

Inspecting the crankshaft components

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Crankcase - crankshaft - connecting rod

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Engine

ENG - 169

Summary of Contents for 150


























































































































































































































































Reviews:

No comments