VESPA 150 Service Station Manual Download

Page: 110 / 249

THROTTLE BODY POSITION SENSOR (TPS)

Function

In charge of sending the size of throttle opening to

the control unit.

Pin-out:

1. Control unit ground

2. Control unit power

3. Throttle position signal

ELECTRICAL ERRORS

Low TPS sensor voltage input P0122

- open circuit or short circuit to negative.

Error cause

Open circuit or short circuit to negative: interruption of the circuit or null voltage at PIN 7, 14 or 18 of

the control unit connector.

Troubleshooting

Open circuit:

- Disconnect control unit and sensor connectors and carry out the check procedure.

- Check the continuity of the cable harness between the sensor connector and control unit connector:

Sensor PIN 1 - control unit PIN 7, sensor PIN 2 - control unit PIN 18 and sensor PIN 3 - control unit PIN

14. If necessary, restore the cable harness.

Short circuit to negative:

- Disconnect the sensor connector.

- Check the ground insulation of the three PIN of the sensor connector.

- If there is no ground insulation restore the cabling.

High sensor voltage input P0123

- shorted to positive.

Error cause

Short circuit to positive: excessive voltage to PIN 7, 14 or 18 of the control unit connector.

Troubleshooting

Short circuit to positive:

- With the sensor connector and the control unit connector disconnected, verify that the fault is shorted

with the battery positive of one of the three PIN of the sensor connector and restore the cable harness.

Electrical system

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ELE SYS - 110

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands