manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 129 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 129

- Separate the components of the driven pulley.

CAUTION

THE TOOL MUST BE FIRMLY FIXED IN THE VICE AND THE
CENTRAL SCREW MUST NOT BE TIGHTENED WITH EX-
CESSIVE TORQUE AS THIS MAY DAMAGE THE PULLEY
OR DEFORM THE SPECIFIC TOOL.

Specific tooling

020444Y

 

Tool for fitting/removing the clutch on

the driven pulley

020444Y011

 

adapter ring

020444Y009

 

wrench 46 x 55

Inspecting the clutch

- Check the thickness of the clutch mass friction

material.

- The masses must exhibit no traces of lubricants;

in that case, check the driven pulley unit seals.

N.B.

UPON RUNNING-IN, THE MASSES MUST EXHIBIT A CEN-
TRAL FAYING SURFACE AND MUST NOT BE DIFFERENT
FROM ONE ANOTHER.
DIFFERENT CONDITIONS MAY CAUSE CLUTCH TEAR-
ING.

CAUTION

DO NOT USE TOOLS TO OPEN THE MASSES TO AVOID
VARIATION IN THE RETURN SPRING LOAD.

Characteristic

Check minimum thickness

1 mm

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Engine

ENG - 129

Summary of Contents for 150


























































































































































































































































Reviews:

No comments