manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 161 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 161

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Piston rings

Removing the piston

- Fit the piston and pin onto the connecting rod,

aligning the piston arrow towards the engine di-

rection of rotation.

CAUTION

AT EVERY NEW MOUNTING USE RETAINER RING PINS.

Choosing the gasket

- First fit the piston into the cylinder, without any base gasket.

- Assemble a dial gauge on the specific tool.

Specific tooling

020942Y

 

Piston protrusion check tool

- With a contrasting surface, reset the dial gauge

with a preloading of a few millimetres.

- Finally fix the dial gauge.

- Check the perfect sliding of the feeler pin.

- Fit the tool on the cylinder without changing the

dial gauge position.

- Lock the tool with the original head fixing nuts.

- Rotate the crankshaft up to TDC (the reversal

point of the dial gauge rotation).

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Engine

ENG - 161

Summary of Contents for 150


























































































































































































































































Reviews:

No comments