VESPA 150 Service Station Manual Download

Page: 178 / 249

Inspection

- Remove the two screws and remove the oil pump

cover.

- Remove and wash the rotors thoroughly with pet-

rol and compressed air.

- Reassemble the rotors in the pump body, keep-

ing the two reference marks visible.

- Using a feeler gauge, check the distance be-

tween the rotors in the position shown in the figure.

- Check the distance between the outer rotor and

pump body, see figure.

Check the axial clearance of the rotors using a

trued bar as shown in the figure.

Characteristic

Axial rotor clearance

Limit values admitted: 0.09 mm

Distance between the outer rotor and the pump
body

Admissible limit clearance: 0.20 mm

Distance between the rotors

Admissible limit clearance: 0.12 mm

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 178

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands