VESPA 150 Service Station Manual Download Page 217

Page: 217 / 249

- Remove the fifth wheel fitting and the dust gaiter

on the steering bearing as shown in figure, using

the specific tool. Proceed giving a few taps with the

mallet.

Specific tooling

020004Y

Punch to remove steering bearings

from headstock

- Refit the fifth wheel fitting and the dust gaiter on

the steering bearing until they stop, using the spe-

cific tool.

Specific tooling

006029Y

Punch for fitting steering bearing seat

on steering tube

Rear

Removing the rear wheel

- Remove the silencer.

- Remove the cotter pin and remove the cap.

- Unscrew the nut fixing the wheel axle and collect

the washer.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Suspensions

SUSP - 217

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 217 / 249

Search results

Summary of Contents for 150

Reviews: