manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 128 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 128

- Using a dial gauge and the magnetic base, meas-

ure the bell eccentricity.

- Repeat the measurement at 3 positions (Central,

internal, external).

- In case of faults, replace the bell.

Specific tooling

020074Y

 

Support base for checking crankshaft

alignment

020335Y

 

Dial gauge magnetic support

Characteristic

clutch bell check: Limit eccentricity.

Admissible limit eccentricity: 0.15 mm

Removing the clutch

- Prepare the locking tool for the driven pulley with

the pins half-screwed in the tool set to «

C

».

- Introduce the adapter ring 11 with the chamfering

facing the inside of the tool.

- Fit the driven pulley unit in the tool so as the bolt

get into the masses clutch support holes. After-

wards make the support screw make contact with

a minimum force.

- Using the specific wrench, inserted 46 mm from

the side, remove the clutch central locking nut.

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 128

Summary of Contents for 150


























































































































































































































































Reviews:

No comments