VESPA 150 Service Station Manual Download

Page: 181 / 249

Piston standard diameter

12.861 + 12.843 mm

Refitting the oil sump

- Refit the by-pass piston in its housing.

- Insert the pressure-regulating spring.

- Fit a new sump seal.

- Refit the sump, taking care to locate the spring in

the appropriate recess machined into the inside of

the sump.

- Refit the rear brake transmission mounting brack-

ets and the screws in the reverse order from which

they were removed.

- Tighten the screws to the prescribed torque.

- Refit the driving pulley assembly, the drive belt,

the sprocket wheel and the transmission cover, as

described in the "Transmission" chapter.

When testing the lubrication system, refer to

the "Crankcase and Crankshaft" chapter, re-

garding lubrication of the connecting rod as-

sembly

Locking torques (N*m)

Locking torque

11 - 13

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Engine

ENG - 181

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands