manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 172 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 172

CAUTION

CAREFULLY CHECK THE CLEANING OF THE BY-PASS
DUCT.
CHECK THAT THE PISTON SLIDES BY HAND, FREELY
AND WITHOUT STICKING.

CAUTION

IT IS ADVISABLE TO INSERT THE CRANKSHAFT IN THE
FLYWHEEL SIDE CRANKCASE HALF TO PREVENT, WITH
ACCIDENTAL MOVEMENTS DURING INSERTION, THE OIL
PUMP CONTROL TOOTHING FROM DAMAGING THE
BUSHINGS.

Locking torques (N*m)

Engine crankcase coupling screws

 

11 - 13

- Complete the coupling operations with the verification of the crankshaft axial clearance.

- Using specific tools to support the dial gauge, verify that the fitting clearance is within the limits.

- Higher clearances are signs of wear of the crankshaft - crankcase supporting surfaces.

Characteristic

Crankshaft-crankcase axial clearance

0.2 to 0.5 mm

Studs

- Using two nuts, fitted as nut and lock nut type,

remove and then drive from the seat.

- Proceed with a thorough cleaning of the threaded

seat on the crankcase.

- Screw the new stud bolts up to the driving depth

indicated.

N.B.

NEW STUD BOLTS DO NOT NEED THREADLOCK, AS
THEY COME EQUIPPED WITH SCOTCH-GRIP.

Characteristic

Driving depth of stud bolts «A»

170 mm+ 0.5

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 172

Summary of Contents for 150


























































































































































































































































Reviews:

No comments