manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 195 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 195

- Remove the connector of the idling adjustment

device.

- Remove the clamps indicated in the figure.

- Disconnect the throttle position sensor connec-

tor.

- Clean the throttle body according to the sched-

uled maintenance.

WARNING

AFTER MAINTENANCE OPERATIONS, IT IS RECOMMEN-
DED TO DELETE THE SELF-ADJUSTABLE PARAMETERS.

Recommended products

Cleaner for throttle bodies

 

Spray cleaner for

throttle bodies

Detergent for throttle bodies

Refitting the butterfly valve

- To refit, follow the operations, but in reverse order, every time the throttle position sensor is discon-

nected it is necessary to calibrate the self-adjusting parameters.

Do not tamper with the stop screws under the

throttle body.

CAUTION

DO NOT TAMPER WITH THE STOP SCREWS UNDER THE
THROTTLE BODY, AS THE IDLE SPEED IS ADJUSTED IN
THE FACTORY.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Injection

INJEC - 195

Summary of Contents for 150


























































































































































































































































Reviews:

No comments