VESPA 150 Service Station Manual Download Page 112

Page: 112 / 249

Open circuit or short circuit to negative: interruption of the circuit or null voltage at PIN 3 of the control

unit connector.

Troubleshooting

Open circuit:

- Disconnect the control unit connector and the heater connector and perform the check procedure.

- Check the continuity of the cable harness between the sensor connector and control unit connector:

Control unit PIN 3 - sensor PIN 2 and control unit PIN 9 - sensor PIN 1. If necessary, restore the cable

harness.

- If the cable harness is intact and the error persists, proceed with the following checks.

Short circuit to negative:

- Disconnect the control unit connector and the heater connector and perform the check procedure.

- Check the sensor connector PIN 2 ground insulation (corresponding to control unit connector PIN 3).

If there is no insulation, restore the cable harness.

High heater lambda probe voltage P0032

- shorted to positive.

Error cause

Short circuit to positive: excessive voltage to PIN 3 of the control unit connector.

Troubleshooting

Short circuit to positive:

- Disconnect the control unit connector and the heater connector and perform the check procedure.

- Verify that there is no short to battery positive on sensor connector PIN 2 (corresponding to control

unit connector PIN 3); if there is a short circuit, restore the cable harness.

IDLE VALVE

Function

Check the minimum engine speed depending on

the temperature and different load conditions.

Pin-out:

1. Negative from control unit (valve activation)

2. Positive from control unit

ELECTRICAL ERRORS

Low idling adjustment device voltage P0508

- open circuit or short circuit to negative.

Error cause

Open circuit or short circuit to negative: interruption of the circuit or null voltage at PIN 1 of the valve

connector.

Troubleshooting

Open circuit:

- Perform the check of the valve and control unit connectors.

Electrical system

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ELE SYS - 112

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 112 / 249

Search results

Summary of Contents for 150

Reviews: