manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 93 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 93

Specification

Desc./Quantity

Power:

 12V - 10W

Quantity:

 2 RHS + 2 LHS

4

Rear daylight bulbs

Type:

 Halogen (HY6W)

Power:

 12V - 6W

Quantity:

 1 RHS + 1 LHS

5

Stop light bulb

Type:

 Incandescent

Power:

12V - 21W

Quantity:

 1

6

License plate light bulb

Type:

 Incandescent

Power:

 12V - 5W

Quantity:

 1

Fuses

The electrical system is protected by a main fuse

and four secondary fuses, positioned as:

MAIN FUSE HOLDER

 «

A

»: battery compartment.

Access to main fuse «A»:

- Remove the battery compartment cover as de-

scribed in «Battery» paragraph.

- Open the fuse holder.

SECONDARY FUSES

 «

B

»: inside the front case.

Access to the secondary fuses «B»:

- Open the front case.

- Open the fuse holders.

CAUTION

BEFORE REPLACING THE FUSE IT IS NECESSARY TO FIND AND SOLVE THE FAILURE THAT
CAUSED IT TO BLOW.
DO NOT REPLACE THE FUSE WITH ANY ALTERNATIVE FORM OF CONDUCTOR.

CAUTION

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Electrical system

ELE SYS - 93

Summary of Contents for 150


























































































































































































































































Reviews:

No comments