VESPA 150 Service Station Manual Download Page 162

Page: 162 / 249

- Measure the deviation from the reset value.

- By means of the table, see the Specifications chapter identify the cylinder base gasket thickness to

be used for refitting. Correctly identify the cylinder base gasket thickness to keep the correct compres-

sion ratio.

- Remove the specific tool and the cylinder.

See also

Slot packing system

Refitting the piston rings

- Pistons (like cylinders) are supplied in 4 catego-

ries: A, B, C and D, and must be fitted so that the

reference arrow faces the exhaust duct. The letter

is found at the centre of the piston.

- Fit the sealing rings with the word TOP or the

identification letter facing upwards. In any case,

the step must be facing opposite the piston crown.

- Sealing rings are manufactured with a cylinder

contact conical cross-section and piston gaps

must be offset by 120° in order to obtain a better

bedding.

- Lubricate rings with engine oil when fitting them.

CAUTION

AT EVERY NEW MOUNTING USE RETAINER RING PINS.

Engine

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

ENG - 162

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

VESPA 150, Service Station Manual, Page: 162 / 249

Search results

Summary of Contents for 150

Reviews: