VESPA 150 Service Station Manual Download

Page: 99 / 249

e - Press the "MF" black button to activate the bat-

tery recharge

Maintenance Free

as shown in fig-

ure.

f - Check the ignition of the green LED indicated

with a red arrow in figure.

g - The activation cycle of the new battery lasts for

30 minutes after the ignition of the recharge LED

has taken place

h - Disconnect the clamps from the battery and

check the voltage, if voltages are detected of less

than 12.8 V, proceed with a new recharge of the

battery starting from point c of the recharge pro-

cedure of

the new battery

, otherwise go to point i

i - The battery is now completely activated, disconnect the battery charger from the fuel supply grid,

disconnect the clamps from the battery and proceed to fitting the battery on the vehicle.

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

Electrical system

ELE SYS - 99

Summary of Contents for 150


























































































































































































































































Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands

VESPA 150, Service Station Manual

Search results

Summary of Contents for 150

Reviews:

Related manuals for 150

Brands by name

Popular brands