manualshive.com logo in svg

VESPA 150, Service Station Manual, Page: 22 / 249

Share
Download
VESPA 150 Service Station Manual Download Page 22

- Measure the diameter of the valve stem at the

three positions indicated in the diagram.

STANDARD DIAMETER

Specification

Desc./Quantity

Inlet:

4.030 to 4.015 mm

Outlet:

4.975 ÷ 4.960 mm

- Calculate the clearance between the valve and its guide.

- Check the deviation of the valve stem by resting

it on a «

V

» shaped support and measuring the ex-

tent of the deformation using a dial gauge.

Characteristic

Limit value allowed:

0.02 mm

- Check the oscillation of the valve head by ar-

ranging a dial gauge at right angle relative to the

valve head and rotate it on a "

V

" shaped abutment.

Characteristic

Limit allowed:

0.3 mm

Measure the valve guides.

Characteristic

Valve guide:

4.3 ± 0.1 mm

Characteristics

Vespa Primavera125 - 150 i.e. 3Valvole (2013)

CHAR - 22

Summary of Contents for 150


























































































































































































































































Reviews:

No comments