Toyota Corolla 2008 Owner'S Manual Download Page 75 | Manualshive

Page: 75 / 310

background image

’08 Corolla_U (L/O 0706)

249

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

If you are a skilled do−it−yourself mechan-
ic, the Toyota service manuals are recom-
mended. Please be aware that do−it−your-
self maintenance can affect your warranty
coverage. See “Owner’s Warranty Informa-
tion Booklet” or “Owner’s Manual Supple-
ment” for the details.

Listed below are the general maintenance
items that should be performed as fre-
quently as specified. In addition to check-
ing the items listed, if you notice any
unusual noise, smell or vibration, you
should investigate the cause or take your
vehicle to your Toyota dealer or a quali-
fied service shop immediately. It is recom-
mended that any problem you notice be
brought to the attention of your dealer or
the qualified service shop for their advice.

CAUTION

Make these checks only with ade-
quate ventilation if you run the en-
gine.

IN THE ENGINE COMPARTMENT

Items listed below should be checked
from time to time, e.g. each time when
refueling.

Washer fluid
Make sure there is sufficient fluid in the
tank. See page 279 in Section 7−3 for
additional information.

Engine coolant level
Make sure the coolant level is between
the “FULL” and “LOW” lines on the see−
through reservoir when the engine is cold.
See page 264 in Section 7−2 for addition-
al information.

Radiator, condenser and hoses
Check that the front of the radiator and
condenser are clean and not blocked with
leaves, dirt, or insects. See page 265 in
Section 7−2 for additional information.

Battery condition
Check the battery condition by the indica-
tor color. See page 276 in Section 7−3 for
additional information.

Brake fluid level
Make sure the brake fluid level is correct.
See page 265 in Section 7−2 for addition-
al information.

Engine oil level
Check the level on the dipstick with the
engine turned off and the vehicle parked
on a level spot. See page 262 in Section
7−2 for additional information.

Power steering fluid level
Check the level through the reservoir. The
level should be in the “HOT” or “COLD”
range depending on the fluid temperature.
See page 266 in Section 7−2 for addition-
al information.

General maintenance

«
...
73
74
75
76
77
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Kargo Master Pages: 5

2013 C-Class Coupe

Brand: Mercedes-Benz Pages: 388

Brand: Standby Pages: 10

Brand: Lexus Pages: 369

Brand: Mountain Top Pages: 12

Brand: Saab Pages: 288

Brand: Sunsky Pages: 9

Brand: Lantronix Pages: 51

MultiCharger 1204

Brand: DEFA Pages: 28

Brand: Steelmate Pages: 14

Brand: Dakota Digital Pages: 20

Perfect Fit MBM120

Brand: Waeco Pages: 3

Brand: Or-Fab Pages: 4

Brand: Toyota Pages: 779

Brand: Aston Martin Pages: 415

Brand: Revelation Pages: 4

Brand: Lexus Pages: 878

MagicWatch MWE850

Brand: Waeco Pages: 200

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands