Toyota Corolla 2008 Owner'S Manual Download Page 205 | Manualshive

Page: 205 / 310

background image

’08 Corolla_U (L/O 0706)

117

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

Vehicles with cruise control—When the
cruise control is being used, even if you
downshift the transmission by pushing and
releasing the overdrive switch, engine
braking will not be enabled because the
cruise control is not cancelled.

For ways to decrease the vehicle speed,
see “Cruise control” on page 131 in this
Section.

CAUTION

Be careful when downshifting on a
slippery surface. Abrupt shifting
could cause the vehicle to skid or
spin.

(e) Using “2” and “L” positions

The “2” and “L” positions are used for
strong engine braking as described pre-
viously.

With the selector lever in “2” or “L”, you
can start the vehicle in motion as with the
lever in “D”.

With the selector lever in “2”, the vehicle
will start in first gear and automatically
shift to second gear.

With the selector lever in “L”, the trans-
mission is engaged in first gear.

NOTICE

Be careful not to over−rev the en-
gine. Watch the tachometer to keep
engine rpm from going into the red
zone. The approximate maximum al-
lowable speed for each position is
given below for your reference:

“2”

118 km/h (73 mph)

. . . . . . . . . . .

“L”

65 km/h (40 mph)

. . . . . . . . . . . .

Do not continue hill climbing or
hard towing for a long time in the
“2” or “L” position. This may cause
severe automatic transmission dam-
age from overheating. To prevent
such damage, “D” position should
be used in hill climbing or hard
towing.

(f) Backing up

1. Bring the vehicle to a complete stop.

2. With the brake pedal held down with

your foot, shift the selector lever to the
“R” position.

NOTICE

Never shift into reverse while the ve-
hicle is moving.

(g) Parking

1. Bring the vehicle to a complete stop.

2. Pull the parking brake lever up fully to

securely apply the parking brake.

3. With the brake pedal pressed down,

shift the selector lever to the “P” posi-
tion.

CAUTION

Never attempt to move the selector
lever into “P” position under any cir-
cumstances while the vehicle is mov-
ing. Serious mechanical damage and
loss of vehicle control may result.

(h) Good driving practice

If the transmission repeatedly shifts up
and down between third gear and over-
drive when climbing a gentle slope, the
overdrive should be turned off. Be sure
to turn the switch on immediately after-
ward.

When towing a trailer, in order to main-
tain engine braking efficiency, do not
use overdrive.

«
...
203
204
205
206
207
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Kathrein Pages: 7

10-8002-C11998B

Brand: Saleen Pages: 12

2013 Buick Verano

Brand: Buick Pages: 5

Brand: Kia Pages: 10

Brand: EEZ RV Pages: 31

Brand: Gator Pages: 8

Brand: E&G Classics Pages: 2

Brand: Improved Racing Pages: 17

A-18 TRAILER ABS

Brand: BENDIX Pages: 40

Brand: Toyota Pages: 56

Brand: Xpresskit Pages: 12

Performer-Plus 2172

Brand: Edelbrock Pages: 4

Brand: TATA Motors Pages: 146

Brand: chinavasion Pages: 3

Brand: Witter Pages: 2

200 CONVERTIBLE 2011

Brand: Chrysler Pages: 5

Brand: Cadillac Pages: 416

Brand: Black & Decker Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands