Toyota Corolla 2008 Owner'S Manual Download Page 128 | Manualshive

Page: 128 / 310

background image

’08 Corolla_U (L/O 0706)

40

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

CAUTION

Persons should ride in their seats
properly wearing their seat belts
whenever the vehicle is moving.
Otherwise, they are much more likely
to suffer serious bodily injury or
death in the event of sudden braking
or a collision.

When using the seat belts, observe
the following:

Use the belt for only one person at
a time. Do not use a single belt for
two or more people—even children.

Avoid reclining the seatback any
more than needed. The seat belts
provide maximum protection in a
frontal or rear collision when the
driver and the front passenger are
sitting up straight and well back in
the seats. If you are reclined, the
lap belt may slide past your hips
and apply restraint forces directly
to the abdomen or your neck may
contact the shoulder belt. In the
event of a frontal collision, the
more the seat is reclined, the great-
er the risk of death or serious inju-
ry.

Be careful not to damage the belt
webbing or hardware. Take care that
they do not get caught or pinched
in the seat or doors.

Inspect the belt system periodically.
Check for cuts, fraying, and loose
parts. Damaged parts should be re-
placed. Do not disassemble or
modify the system.

Keep the belts clean and dry. If
they need cleaning, use a mild soap
solution or lukewarm water. Never
use bleach, dye, or abrasive clean-
ers, or allow them to come into
contact with the belts—they may
severely weaken the belts. (See
“Cleaning the interior” on page 243
in Section 5.)

Replace the belt assembly (includ-
ing bolts) if it has been used in a
severe impact. The entire assembly
should be replaced even if damage
is not obvious.

Tab

Buckle

Adjust the seat as needed and sit up
straight and well back in the seat. To
fasten your belt, pull it out of the re-
tractor and insert the tab into the
buckle.

You will hear a click when the tab locks
into the buckle.

The seat belt length automatically adjusts
to your size and the seat position.

The retractor will lock the belt during a
sudden stop or on impact. It also may
lock if you lean forward too quickly. A
slow, easy motion will allow the belt to
extend, and you can move around freely.

—Fastening front and rear
seat belts

«
...
126
127
128
129
130
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Taffio Pages: 8

CHASSIS CAB 3500 2017

Brand: RAM Pages: 16

Brand: Raytel LLC Pages: 40

Brand: Renault Pages: 340

Brand: Cadillac Pages: 402

Brand: Cobra Pages: 2

PRIME DESIGN HRR-369-E-UM3-96

Brand: Safe Fleet Pages: 12

Brand: Kocchi's Pages: 4

Brand: Lantronix Pages: 51

Brand: Mercedes-Benz Pages: 398

Brand: Thule Pages: 2

Brand: true-i Pages: 11

Brand: PUTCO Pages: 3

OUTLANDER PHEV 2022

Brand: Mitsubishi MOTORS Pages: 8

Brand: Reliant Pages: 116

Brand: Axxess Pages: 4

Brand: Nos Pages: 22

Brand: Macally Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands