Toyota Corolla 2008 Owner'S Manual Download Page 42 | Manualshive

Page: 42 / 310

background image

’08 Corolla_U (L/O 0706)

216

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

When restarting out after parking on a
slope:

1. With the transmission in “P” position

(automatic) or the clutch pedal de-
pressed (manual), start the engine.
(With an automatic transmission, be
sure to keep the brake pedal de-
pressed.)

2. Shift into gear.

3. Release the parking brake (also foot

brake on automatic transmission ve-
hicles) and slowly pull or back away
from the wheel blocks. Stop and apply
your brakes.

4. Have someone retrieve the blocks.

CAUTION

Do not exceed 72 km/h (45 mph) or
the posted towing speed limit,
whichever is lower. Because insta-
bility (swaying) of a towing vehicle−
trailer combination usually in-
creases as the speed increases, ex-
ceeding 72 km/h (45 mph) may
cause loss of control.

Slow down and downshift before
descending steep or long downhill
grades. Do not make sudden down-
shifts.

Avoid holding the brake pedal down
too long or too frequently. This
could cause the brakes to overheat
and result in reduced braking effi-
ciency.

Improving fuel economy is easy—just take
it easy. It will help make your vehicle last
longer, too. Here are some specific tips
on how to save money on both fuel and
repairs:

Keep your tires inflated at the cor-
rect pressure. Underinflation causes
tire wear and wastes fuel. See page
267 in Section 7−2 for instructions.

Do not carry unneeded weight in
your vehicle. Excess weight puts a
heavier load on the engine, causing
greater fuel consumption.

Avoid lengthy warm−up idling. Once
the engine is running smoothly, begin
driving—but gently. Remember, howev-
er, that on cold winter days this may
take a little longer.

Keep the automatic transmission
overdrive turned on when engine
braking is not required. Driving with
the overdrive off will reduce the fuel
economy. (For details, see “Automatic
transmission” on page 115 in Section
1−7.)

Accelerate slowly and smoothly.
Avoid jackrabbit starts. Get into high
gear as quickly as possible.

How to save fuel and make
your vehicle last longer

«
...
40
41
42
43
44
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Metra Electronics Pages: 14

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Wallbox Pages: 7

Brand: Mercedes-Benz Pages: 30

Brand: AutoWatch Pages: 4

Brand: Hank Pages: 2

Brand: STARLANE Pages: 24

Brand: THIEYE Pages: 88

Brand: Acura Pages: 6

2010 MX-5 Miata

Brand: Mazda Pages: 8

RAV-4 2015 Series

Brand: Toyota Pages: 50

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

Brand: KLAUS Multiparking Pages: 72

Ridesmart KMA-610

Brand: KlipXtreme Pages: 12

Brand: Kuda Pages: 3

Brand: PEUGEOT Pages: 404

Brand: Rajant Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands