Toyota Corolla 2008 Owner'S Manual Download Page 49 | Manualshive

Page: 49 / 310

background image

’08 Corolla_U (L/O 0706)

223

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

5. Start your engine in the normal way.

After starting, run it at about 2000 rpm
for several minutes with the accelerator
pedal lightly depressed.

6. Carefully disconnect the cables in the

exact reverse order: the negative cable
and then the positive cable.

7. Carefully dispose of the battery cover

cloths—they may now contain sulfuric
acid.

8. If removed, replace all the battery vent

plugs.

If the cause of your battery discharging is
not apparent (for example, lights left on),
you should have it checked at your Toyota
dealer.

If the first start attempt is not success-
ful...

Check that the clamp on the jumper
cables are tight. Recharge the discharged
battery with the jumper cables connected
for several minutes and restart your en-
gine in the normal way.

If the another attempt is not successful,
the battery may be depleted. Have it ch-
ecked at your Toyota dealer.

If your engine stalls while driving...

1. Reduce your speed gradually, keeping

a straight line. Move cautiously off the
road to a safe place.

2. Turn on your emergency flashers.

3. Turn the ignition key to “ACC” or

“LOCK”, and try starting the engine
again.

If the engine will not start, see “If your
vehicle will not start” on page 220 in this
Section.

CAUTION

If the engine is not running, the pow-
er assist for the brakes and steering
will not work so steering and braking
will be much harder than usual.

If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.

At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your vehicle
checked by your Toyota dealer as soon as
possible.

Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, the system may not be
recovered until the engine is stopped and
the ignition key is turned to “ACC” or
“LOCK” position.

CAUTION

Be especially careful to prevent erro-
neous pedal operation.

If your engine stalls while
driving

If you cannot increase engine
speed

«
...
47
48
49
50
51
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Ignition Pages: 1

2011 grand cherokee

Brand: Jeep Pages: 22

2013 Grand Cherokee

Brand: Jeep Pages: 704

Brand: Jeep Pages: 558

Car Cup Holder Phone Mount

Brand: UGREEN Pages: 9

Code Alarm PROFESSIONAL SERIES CA 5550SST

Brand: Audiovox Pages: 14

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

STO N SHO SNS 144

Brand: Big Mikes Performance Parts Pages: 7

Brand: Lincoln Pages: 10

Brand: EUFAB Pages: 12

Brand: Oldsmobile Pages: 354

Brand: Black+Decker Pages: 21

Brand: Beeper Pages: 20

Brand: Prorack Pages: 15

Brand: Westfalia Pages: 10

Brand: Prorack Pages: 14

Brand: Lexus Pages: 830

Brand: ZENEC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands