Toyota Corolla 2008 Owner'S Manual Download Page 68 | Manualshive

Page: 68 / 310

background image

’08 Corolla_U (L/O 0706)

242

2008 COROLLA from Aug. ’07 Prod. (OM12B28U)

Aluminum wheels: Use only a mild soap
or neutral detergent.

NOTICE

Do not use corrosive chemical−
based cleaners on your wheels.
(Example: hydrofluoric acid)

Do not use steam cleaners or the
chemicals therein to clean your
wheels.

Do not use scouring pads, wire
brushes, or coarse abrasives to
clean your wheels.

Do not use alcohol, solvents, gaso-
line, or other non−neutral deter-
gents, because they may alter the
wheel’s appearance and resistance
to corrosion.

Plastic bumpers: Wash carefully. Do not
scrub with abrasive cleaners. The bumper
faces are soft.

Exterior lights: Wash carefully. Do not use
organic substances or scrub them with a
hard brush. This may damage the sur-
faces of the lights.

Road tar: Remove with turpentine or
cleaners that are marked safe for painted
surfaces.

3. Rinse thoroughly—dried soap can

cause streaking. In hot weather you
may need to rinse each section right
after you wash it.

4. To prevent water spots, dry the vehicle

using a clean soft cotton towel. Do not
rub or press hard—you might scratch
the paint.

NOTICE

Do not use organic substances
(gasoline, kerosene, benzine or
strong solvents), which may be tox-
ic or cause damage.

Do not scrub any part of the ve-
hicle with a hard brush, which may
cause damage.

Automatic car wash

Your vehicle may be washed in an auto-
matic car wash, but remember that the
paint can be scratched by some types of
brushes, unfiltered washing water, or the
washing process itself. Scratching reduces
paint durability and gloss, especially on
darker colors. The manager of the car
wash should be able to advise you wheth-
er the process is safe for the paint on
your vehicle.

NOTICE

To prevent damage to the antenna,
make sure it is removed before driv-
ing your Toyota through an automatic
car wash.

Waxing your Toyota

Polishing and waxing is recommended
to maintain the original beauty of your
Toyota’s finish.

Apply wax once a month or if the vehicle
surface does not repel water well.

1. Always wash and dry the vehicle be-

fore you begin waxing, even if you are
using a combined cleaner and wax.

«
...
66
67
68
69
70
...
»

Summary of Contents for Corolla 2008























































































































































































































































































































Reviews:

No comments

Related manuals for Corolla 2008

Brand: Quadratec Pages: 8

Brand: 3SIXT Pages: 12

Brand: BESAFE Pages: 4

Brand: Saab Pages: 3

Brand: Phonocar Pages: 2

Brand: BMW Pages: 21

Green Motion DC 66

Brand: Eaton Pages: 18

STEALTH POWER RBP-216-SP

Brand: RBP Pages: 16

STREET SUPER SHIFTER

Brand: HURST Pages: 2

Brand: MASCOT Pages: 12

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: Xblitz Pages: 30

Brand: STARLANE Pages: 24

Brand: E&G Classics Pages: 2

Brand: BMW Pages: 189

Brand: Jaeger Pages: 11

Brand: Kia Pages: 680

Dodge Caravan 2002

Brand: Chrysler Pages: 2399

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands